![sonicwall netextender login server unreachable sonicwall netextender login server unreachable](http://help.sonicwall.com/help/sw/eng/8112/8/0/0/content/images/Edit_User_NetExtender.png)
- #Sonicwall netextender login server unreachable update
- #Sonicwall netextender login server unreachable series
- #Sonicwall netextender login server unreachable mac
![sonicwall netextender login server unreachable sonicwall netextender login server unreachable](https://e3effa51eee72fd900e3-2fb779bd12ec72d4612275342f2c9187.ssl.cf1.rackcdn.com/ae5d80eed71bf5835725d80eb36a4994.jpg)
Timeout for conflicted resource to be rechecked: 1800 Seconds Never add static default routes to the NSM route databaseĭHCP Server Conflict Detect Period: 300 Seconds Perform SYN validation when not operating in strict TCP compliance modeĪllow first fragment of size lesser than 68 bytesĭisable learning-bridge filtering on L2 bridge interfaces
#Sonicwall netextender login server unreachable update
Update route version when route is enabled/disabled (affects existing connections)
#Sonicwall netextender login server unreachable mac
Ignore ARPs with primary-gateway’s MAC received on other interfacesįlush flows on alternate path when normal route path is enabled (affects existing connections) Periodically broadcast system ARPs every 60 minutes. Never broadcast more than 100 Gratuitous ARPs in any 60 second period. Only allow ARP entries with unicast addressesīypass ARP processing on L2 bridge interfaces Enjoy!Įnable open ARP behavior (WARNING: Insecure!!)Įnable Source IP Address validation for being directly connected Keep in mind these options are undocumented, unsupported, and it is suggested to only make changes to these values if instructed by Dell Technical Support. Below is a rough list of some of the options. For me the option I needed was “Disable Port Scan Detection” under the Firewall section. Under Internal Settings there are quite a few settings and options. On the main page you will see the following disclaimer.
#Sonicwall netextender login server unreachable series
It appears to be available in all of the TZ series devices, the SOHO, and likely others. I also checked the connectivity_tool.log but it just reports no issues or connectivity problems detected.SonicWALL Hidden Features and Configuration OptionsĮarlier I stumbled across a hidden set of features and settings in a TZ215 by going to /diag.html and figured Id share this with everyone in case you were unaware of it as I was.
![sonicwall netextender login server unreachable sonicwall netextender login server unreachable](http://help.sonicwall.com/help/sw/eng/published/7.0.0_130815_1115/content/Chapter13_GeoIP_Botnet/Geo_AccessPoliciesInset.png)
![sonicwall netextender login server unreachable sonicwall netextender login server unreachable](https://us.v-cdn.net/6031761/uploads/70W89QILAQMG/image.png)
I even went so far as to change the hostname to the SRA’s IP address, which gave me a different result in the log to the effect of “valid IP” but like I said, no change in the overall behavior. I learned this was picked up from the SRA’s configured hostname under Network > DNS > SRA Appliance Hostname, and it actually didn’t matter whether I configured it to be a resolvable hostname or not. (Note: “ ” is not the actual data in the log, I just changed it here for privacy.) The only error I see here is between the auth and preauth stage with the following line: The log pretty much stops at that point but then it repeats this process for that second Duo push. Logging you in…’ and it sent the response. Then Duo authentication returned ‘allow’: ‘Success. Please contact your administrator or try again later.”Īccording to the authproxy.log it shows preauth was successful then it triggered a push notification. Before timing out, the user will receive one more push notification, wait a while, then the SRA webpage or NetExtender will return an error “Login server unreachable. Our configuration is using for preauthentication, and the strange thing is that if a user tries to login with either NetExtender or the SSL VPN SRA webpage using configuration, it will send a push notification to the user’s Duo Mobile app but nothing happens after that point. We’re trying to setup Duo to integrate with our SonicWALL SRA 4200 and so far it is successful with the primary configuration using, however I’m looking to have this work with NetExtender as well but that doesn’t seem to be working when using the SonicWALL SRA alternative configuration at SonicWALL SRA or SMA 100 Series SSL with RADIUS Auto Push for VPN Client Access | Duo Security and.